Ham Tech Exam β€Ί Question pool β€Ί T7

T7: Practical Circuits questions (2026–2030 Technician pool)

44 questions in the pool Β· 4 on your exam Β· official NCVEC 2026–2030 pool (public domain)

All 44 questions from subelement T7, Practical Circuits, with the correct answer marked. Your exam draws one question from each group below, so you'll see 4 T7 questions. On test day the answer order can be shuffled, so learn the answer, not the letter. Tap "Why" for a plain-English explanation.

Groups: T7A Β· T7B Β· T7C Β· T7D

T7A (11 questions, 1 on your exam)

T7A01: Which term describes the ability of a receiver to detect the presence of a signal?
  • A. RF gain
  • B. Sensitivity βœ“
  • C. Selectivity
  • D. Total Harmonic Distortion
Why, and a memory hook

Sensitivity is the ability of a receiver to detect (hear) the presence of a signal, including weak ones.

Memory hook: Sensitivity = hear the weak ones.

T7A02: What is a transceiver?
  • A. A device that combines a receiver and transmitter βœ“
  • B. A device for matching feed line impedance to 50 ohms
  • C. A device for automatically sending and decoding Morse code
  • D. A device for converting receiver and transmitter frequencies to another band
Why, and a memory hook

A transceiver combines a transmitter and a receiver in one unit.

Memory hook: Trans + ceiver = both.

T7A03: Which of the following is used to convert a signal from one frequency to another?
  • A. Phase splitter
  • B. Mixer βœ“
  • C. Inverter
  • D. Amplifier
Why, and a memory hook

A mixer combines two signals to convert a signal from one frequency to another.

Memory hook: Mixer shifts frequency.

T7A04: Which term describes the ability of a receiver to discriminate between multiple signals?
  • A. Discrimination ratio
  • B. Sensitivity
  • C. Selectivity βœ“
  • D. Harmonic distortion
Why, and a memory hook

Selectivity is the ability of a receiver to discriminate between signals on nearby frequencies.

Memory hook: Selectivity = pick one signal.

T7A05: What is the name of a circuit that generates a signal at a specific frequency?
  • A. Reactance modulator
  • B. Phase modulator
  • C. Low-pass filter
  • D. Oscillator βœ“
Why, and a memory hook

An oscillator is a circuit that generates a signal at a specific frequency.

Memory hook: Oscillator = signal source.

T7A06: What device converts the RF input and output of a transceiver to another band?
  • A. High-pass filter
  • B. Low-pass filter
  • C. Transverter βœ“
  • D. Phase converter
Why, and a memory hook

A transverter converts the RF input and output of a transceiver to another band.

Memory hook: Transverter = band translator.

T7A07: What is the function of a transceiver’s PTT input?
  • A. Input for a key used to send CW
  • B. Switches transceiver from receive to transmit when grounded βœ“
  • C. Provides a transmit tuning tone when grounded
  • D. Input for a preamplifier tuning tone
Why, and a memory hook

The PTT (push-to-talk) input switches the transceiver from receive to transmit when it is grounded.

Memory hook: Ground the PTT to transmit.

T7A08: Which of the following describes combining speech with an RF carrier signal?
  • A. Impedance matching
  • B. Oscillation
  • C. Modulation βœ“
  • D. Low-pass filtering
Why, and a memory hook

Modulation is the process of combining speech (or other information) with an RF carrier signal.

Memory hook: Modulation = put the message on the carrier.

T7A09: What is the function of the switch which selects either SSB or CW-FM on some VHF power amplifiers?
  • A. Change the mode of the transmitted signal
  • B. Set the amplifier for proper operation in the selected mode βœ“
  • C. Change the frequency range of the amplifier to operate in the proper segment of the band
  • D. Reduce the received signal noise
Why, and a memory hook

The mode switch on some VHF amplifiers sets the amplifier for proper operation in the selected mode, such as SSB versus CW-FM.

Memory hook: Match the amp to the mode.

T7A10: What can be added to the output of a transceiver to increase the transmitted output power?
  • A. A potentiometer
  • B. An RF power amplifier βœ“
  • C. An impedance multiplier
  • D. All these choices are correct
Why, and a memory hook

An RF power amplifier added to the transceiver output increases the transmitted power.

Memory hook: Amplifier adds power.

T7A11: What is the function of the Variable Frequency Oscillator (VFO) circuit in a transceiver?
  • A. Set the receive and transmit frequency βœ“
  • B. Provide automatic frequency control
  • C. Inject a variable frequency to allow CW reception
  • D. Generate and demodulate single sideband signals
Why, and a memory hook

The VFO sets the receive and transmit frequency in a transceiver.

Memory hook: VFO = frequency setter.

T7B (11 questions, 1 on your exam)

T7B01: What can you do if you are told your FM handheld or mobile transceiver is over-deviating?
  • A. Talk louder into the microphone
  • B. Let the transceiver cool off
  • C. Change to a higher power level
  • D. Talk farther away from the microphone βœ“
Why, and a memory hook

Over-deviation means too much audio is modulating the FM signal, so talk farther from the microphone or speak more softly.

Memory hook: Back off the mic.

T7B02: What would cause a broadcast AM or FM radio to receive an amateur radio transmission unintentionally?
  • A. The receiver is unable to reject strong signals outside the AM or FM band βœ“
  • B. The microphone gain of the transmitter is turned up too high
  • C. The audio amplifier of the transmitter is overloaded
  • D. The deviation of an FM transmitter is set too low
Why, and a memory hook

Broadcast receivers can pick up amateur signals when the receiver cannot reject strong signals outside its intended band. Overload is the receiver's problem, not a harmonic from the amateur station.

Memory hook: Receiver overload from strong signals.

T7B03: Which of the following can cause radio frequency interference?
  • A. Fundamental overload
  • B. Harmonics
  • C. Spurious emissions
  • D. All these choices are correct βœ“
Why, and a memory hook

Radio frequency interference can come from fundamental overload, harmonics, and spurious emissions, so all the choices can cause it.

Memory hook: Overload, harmonics, spurs: all cause RFI.

T7B04: Which of the following might be the cause of low RF power output from a solid-state transceiver?
  • A. Poor amplifier noise figure
  • B. Poor amplifier linearity
  • C. Low SWR
  • D. High SWR βœ“
Why, and a memory hook

High SWR makes solid-state transmitters automatically reduce power to protect the output transistors, resulting in low output power.

Memory hook: High SWR cuts the power.

T7B05: Which of the following might reduce interference by an amateur station to a non-amateur over-the-air radio receiver?
  • A. Block the amateur signal with a filter at the antenna input of the affected receiver βœ“
  • B. Block the interfering signal with a filter on the amateur transmitter
  • C. Switch the transmitter from FM to SSB
  • D. Switch the transmitter to a narrow-band mode
Why, and a memory hook

Blocking the amateur signal with a filter at the antenna input of the affected receiver can reduce interference, since the fix belongs at the receiver front end.

Memory hook: Filter at the victim's receiver.

T7B06: Which of the following actions should you take if a neighbor tells you that your station’s transmissions are interfering with their radio or TV reception?
  • A. Make sure that your station is functioning properly and that it does not cause interference to your own radio or television when it is tuned to the same channel βœ“
  • B. Immediately turn off your transmitter and contact the nearest FCC office for assistance
  • C. Install a harmonic doubler on the output of your transmitter and tune it until the interference is eliminated
  • D. All these choices are correct
Why, and a memory hook

First make sure your own station is functioning properly and that it does not interfere with your own radio or TV tuned to the same channel. Then you can look for other causes. [97.121]

Memory hook: Check your own gear first.

T7B07: Which of the following can reduce interference to a 2-meter band transceiver from a nearby commercial FM station?
  • A. Installing an RF preamplifier
  • B. Using double-shielded coaxial cable
  • C. Installing bypass capacitors on the microphone cable
  • D. Installing a band-reject filter βœ“
Why, and a memory hook

A band-reject filter (notch) that rejects the FM broadcast band can reduce interference to a 2-meter receiver from a nearby commercial FM station.

Memory hook: Reject the broadcast band.

T7B08: What should you do if something in a neighbor’s home is causing harmful interference to your amateur station?
  • A. Work with your neighbor to identify the offending device
  • B. Politely inform your neighbor that FCC rules prohibit the use of devices that cause interference
  • C. Make sure your station meets the standards of good amateur practice
  • D. All these choices are correct βœ“
Why, and a memory hook

If your neighbor's equipment is interfering with your station, you may work with your neighbor, politely inform them, and check your own station, so all the choices apply. [97.101(a)]

Memory hook: Be polite and check everything.

T7B09: What should be the first step to resolve non-fiber optic cable TV interference caused by your amateur radio transmission?
  • A. Add a low-pass filter to the TV antenna input
  • B. Add a high-pass filter to the TV antenna input
  • C. Add a preamplifier to the TV antenna input
  • D. Be sure all TV feed line coaxial connectors are installed properly βœ“
Why, and a memory hook

For non-fiber cable TV interference, first be sure all TV feed line coaxial connectors are installed properly, since a loose connector or poor shielding lets RF in.

Memory hook: Check the TV coax connectors first.

T7B10: What might be a problem if you receive a report that your audio signal through an FM repeater is distorted or unintelligible?
  • A. Your transmitter is slightly off frequency
  • B. You are speaking too loudly or too close to the microphone
  • C. You are in a bad location
  • D. All these choices are correct βœ“
Why, and a memory hook

Distorted repeater audio can be caused by over-deviation, low battery voltage, or being off frequency, so any of the listed choices can be the problem.

Memory hook: Distortion has many causes.

T7B11: Which of the following can eliminate distorted voice transmissions?
  • A. Adding extra feedline to the antenna to lower SWR
  • B. Turning the radio on and off to reset the computer-controlled circuitry
  • C. Adding a clip-on ferrite β€œchoke” to the microphone cable to prevent the transmitted signal from feeding back into the transmitter βœ“
  • D. Turning the squelch control fully clockwise to prevent the transmitted signal from triggering the squelch circuit
Why, and a memory hook

Distorted voice can be caused by RF feeding back into the microphone cable, and a clip-on ferrite choke can stop that.

Memory hook: Ferrite chokes block RF on the mic cable.

T7C (11 questions, 1 on your exam)

T7C01: What is the primary purpose of a dummy load?
  • A. To prevent transmitting signals over the air when making tests βœ“
  • B. To prevent over-modulation of a transmitter
  • C. To improve the efficiency of an antenna
  • D. To improve the signal-to-noise ratio of a receiver
Why, and a memory hook

A dummy load absorbs the transmitter's power so you can make tests without radiating signals over the air.

Memory hook: Dummy load = test without transmitting.

T7C02: Which of the following is used to determine if an antenna is resonant at the desired operating frequency?
  • A. A VTVM
  • B. An antenna analyzer βœ“
  • C. A Q meter
  • D. A frequency counter
Why, and a memory hook

An antenna analyzer measures SWR and impedance over a frequency range, so you can see whether the antenna is resonant at the desired frequency.

Memory hook: Analyzer shows resonance.

T7C03: What does a typical RF dummy load consist of?
  • A. A low-voltage power supply and an AC relay
  • B. A 50-ohm non-inductive resistor mounted on a heat sink βœ“
  • C. A low-voltage power supply and a DC relay
  • D. A 50-ohm inductive reactance mounted in a shielded enclosure
Why, and a memory hook

A typical dummy load is a 50-ohm non-inductive resistor mounted on a heat sink.

Memory hook: 50 ohms, non-inductive, heat sink.

T7C04: What reading on an SWR meter indicates a perfect impedance match between the antenna and the feed line?
  • A. 50:50
  • B. Zero
  • C. 1:1 βœ“
  • D. Full Scale
Why, and a memory hook

An SWR of 1:1 means a perfect impedance match, with no reflected power.

Memory hook: One to one is perfect.

T7C05: Why do most solid-state transmitters reduce output power as SWR increases beyond a certain level?
  • A. To protect the RF output amplifier transistors βœ“
  • B. To comply with FCC rules on spectral purity
  • C. Because power supplies cannot supply enough current at high SWR
  • D. To lower the SWR on the transmission line
Why, and a memory hook

Most solid-state transmitters reduce power as SWR rises to protect the output transistors from excess current and heat.

Memory hook: Protect the finals.

T7C06: What does an SWR reading of 4:1 indicate?
  • A. Loss of -4 dB
  • B. Good impedance match
  • C. Gain of +4 dB
  • D. Impedance mismatch βœ“
Why, and a memory hook

An SWR of 4:1 indicates an impedance mismatch. A perfect match is 1:1.

Memory hook: Higher SWR means more mismatch.

T7C07: What happens to power lost in a feed line?
  • A. It increases the SWR
  • B. It is radiated as harmonics
  • C. It is converted into heat βœ“
  • D. It distorts the signal
Why, and a memory hook

Power lost in a feed line is converted into heat.

Memory hook: Lost power turns to heat.

T7C08: Which instrument can be used to determine SWR?
  • A. Voltmeter
  • B. Ohmmeter
  • C. Iambic pentameter
  • D. Directional wattmeter βœ“
Why, and a memory hook

A directional wattmeter measures forward and reflected power, from which SWR is determined.

Memory hook: Forward and reflected give SWR.

T7C09: Which of the following causes failure of coaxial cables?
  • A. Moisture contamination βœ“
  • B. Solder flux contamination
  • C. Rapid fluctuation in transmitter output power
  • D. Operation at 100% duty cycle for an extended period
Why, and a memory hook

Moisture contamination is a common cause of coaxial cable failure.

Memory hook: Water ruins coax.

T7C10: Why should the outer jacket of coaxial cable be resistant to ultraviolet light?
  • A. Ultraviolet light can increase the resistance of the conductors
  • B. Ultraviolet light can increase losses in the cable’s jacket
  • C. Ultraviolet and RF signals can mix, causing interference
  • D. Ultraviolet light can damage the jacket and allow water to enter the cable βœ“
Why, and a memory hook

Ultraviolet light can damage the jacket and allow water to enter the cable, which degrades it.

Memory hook: UV cracks the jacket, water gets in.

T7C11: What is an advantage of foam-dielectric versus solid-dielectric coaxial cable?
  • A. It is more resistant to moisture contamination
  • B. It has higher voltage breakdown
  • C. It has less loss per foot βœ“
  • D. It has a better impedance match to 50 ohms
Why, and a memory hook

Foam-dielectric coax has less loss per foot than solid-dielectric coax.

Memory hook: Foam means less loss.

T7D (11 questions, 1 on your exam)

T7D01: Which instrument would you use to measure electric potential?
  • A. An ammeter
  • B. A voltmeter βœ“
  • C. A potentiometer
  • D. An ohmmeter
Why, and a memory hook

A voltmeter measures electric potential (voltage).

Memory hook: Volt meter measures volts.

T7D02: How is a voltmeter connected to a component to measure applied voltage?
  • A. In series
  • B. In parallel βœ“
  • C. In quadrature
  • D. In phase
Why, and a memory hook

A voltmeter is connected in parallel with the component whose voltage you want to measure.

Memory hook: Voltmeter in parallel.

T7D03: When configured to measure current, how is a multimeter connected to a component?
  • A. In series βœ“
  • B. In parallel
  • C. In quadrature
  • D. In phase
Why, and a memory hook

To measure current, a multimeter is connected in series so all the current flows through the meter.

Memory hook: Ammeter in series.

T7D04: Which instrument is used to measure electric current?
  • A. An ohmmeter
  • B. An electrometer
  • C. A voltmeter
  • D. An ammeter βœ“
Why, and a memory hook

An ammeter measures electric current.

Memory hook: Ammeter measures amps.

T7D05: How does an ohmmeter measure the resistance of a circuit or component?
  • A. By applying a small current and measuring the resulting voltage βœ“
  • B. By placing a variable resistor in parallel with the circuit
  • C. By placing a variable resistor in series with the circuit
  • D. By applying a variable voltage and measuring the resulting current change
Why, and a memory hook

An ohmmeter applies a small current to the component and measures the resulting voltage, then computes resistance from it.

Memory hook: Ohmmeter pushes current, reads voltage.

T7D06: Which of the following can damage a multimeter?
  • A. Attempting to measure resistance using the voltage setting
  • B. Failing to connect one of the probes to ground
  • C. Attempting to measure voltage when using the resistance setting βœ“
  • D. Not allowing it to warm up properly
Why, and a memory hook

Attempting to measure voltage while the meter is set to resistance can damage the meter, since the ohms range is not designed to take external voltage.

Memory hook: Never read volts on the ohms range.

T7D07: Which of the following measurements are made using a multimeter?
  • A. Signal strength and noise
  • B. Impedance and reactance
  • C. Voltage and resistance βœ“
  • D. All these choices are correct
Why, and a memory hook

A multimeter can measure voltage, current and resistance, so voltage and resistance are among its measurements.

Memory hook: Multimeter: volts, amps, ohms.

T7D08: Which of the following types of solder should not be used for radio and electronic applications?
  • A. Acid-core solder βœ“
  • B. Lead-tin solder
  • C. Rosin-core solder
  • D. Tin-copper solder
Why, and a memory hook

Acid-core solder is meant for plumbing and its corrosive flux damages electronics. Use rosin-core solder for electronic work.

Memory hook: Rosin for radios, acid for pipes.

T7D09: What is the characteristic appearance of a cold tin-lead solder joint?
  • A. Dark black spots
  • B. A bright or shiny surface
  • C. A rough or lumpy surface βœ“
  • D. A greenish tinge
Why, and a memory hook

A cold solder joint has a rough or lumpy surface instead of a smooth, shiny one.

Memory hook: Cold joint looks rough.

T7D10: What reading indicates that an ohmmeter is connected across a large, discharged capacitor?
  • A. Increasing resistance with time βœ“
  • B. Decreasing resistance with time
  • C. Steady full-scale reading
  • D. Alternating between open and short circuit
Why, and a memory hook

Across a large discharged capacitor an ohmmeter's current charges the capacitor, so the resistance reading increases with time.

Memory hook: Charging capacitor, rising resistance.

T7D11: Which of the following precautions should be taken when measuring in-circuit resistance with an ohmmeter?
  • A. Ensure that the applied voltages are correct
  • B. Ensure that the circuit is not powered βœ“
  • C. Ensure that the circuit is grounded
  • D. Ensure that the circuit is operating at the correct frequency
Why, and a memory hook

When measuring in-circuit resistance, make sure the circuit is not powered, because applied voltage would give false readings and could damage the meter.

Memory hook: Power off before ohms.

Test yourself on these

Take a free 35-question practice exam drawn one per group, just like the real thing.

Start the free practice test

← T6: Electronic and Electrical ComponentsAll subelementsT8: Signals and Emissions β†’

Sources

  1. NCVEC: 2026–2030 Technician Question Pool (public release and errata)
  2. 47 CFR Β§ 97.503: Element standards (35 questions, 26 to pass)

Want the why behind all 409 questions?

Ham Tech Exam is a Technician study app that explains every answer with a memory hook. Join the list to get the beta first and the launch-day price.

One email when the beta opens, one at launch. No spam. Unsubscribe anytime by emailing [email protected].