T4: Amateur Radio Practices questions (2026–2030 Technician pool)

23 questions in the pool · 2 on your exam · official NCVEC 2026–2030 pool (public domain)

All 23 questions from subelement T4, Amateur Radio Practices, with the correct answer marked. Your exam draws one question from each group below, so you'll see 2 T4 questions. On test day the answer order can be shuffled, so learn the answer, not the letter. Tap "Why" for a plain-English explanation.

Groups: T4A · T4B

T4A (12 questions, 1 on your exam)

T4A01: Which of the following is an appropriate power supply rating for a typical 50-watt output mobile FM transceiver?
  • A. 24.0 volts at 4 amperes
  • B. 13.8 volts at 4 amperes
  • C. 24.0 volts at 12 amperes
  • D. 13.8 volts at 12 amperes ✓
Why, and a memory hook

A 50-watt FM mobile rig draws about 10 to 12 amperes at 13.8 volts, so a 13.8 V supply rated for 12 A is appropriate.

Memory hook: Mobile = 13.8 V and enough amps.

T4A02: Which of the following should be considered when selecting an accessory SWR meter?
  • A. The frequency and power level at which the measurements will be made ✓
  • B. The distance that the meter will be located from the antenna
  • C. The maximum SWR anticipated on the transmission line
  • D. The ability of the meter to compensate for a poor transmission line match to the antenna
Why, and a memory hook

An SWR meter is designed for particular frequency ranges and power levels, so choose one rated for the frequency and power you will use.

Memory hook: Match the meter to band and power.

T4A03: Why are short, heavy-gauge wires used for a transceiver’s DC power connection?
  • A. To minimize voltage drop when transmitting ✓
  • B. To provide a close match to the power supply output impedance
  • C. To avoid RF interference
  • D. To minimize radiative losses in the power cable
Why, and a memory hook

Short, heavy-gauge wires have low resistance, which minimizes voltage drop when the radio draws high current while transmitting.

Memory hook: Short and thick drops less voltage.

T4A04: How are the audio input and output of a transceiver connected in a station configured to operate using FT8?
  • A. To a computer running a terminal program and connected to a terminal node controller unit
  • B. To the audio output and input of a computer running FT8 software ✓
  • C. To an FT8 conversion unit, a keyboard, and a computer monitor
  • D. To a computer connected to the FT8converter.com website
Why, and a memory hook

For FT8 the transceiver's audio output goes to the computer's audio input and the computer's audio output goes to the transceiver's audio input, so the software can decode and generate the tones.

Memory hook: Radio out to computer in; computer out to radio in.

T4A05: Where should an RF power meter be installed?
  • A. In the feed line, between the transmitter and antenna ✓
  • B. At the power supply output
  • C. In parallel with the push-to-talk line and the antenna
  • D. In the power supply cable, as close as possible to the radio
Why, and a memory hook

An RF power meter goes in the feed line between the transmitter and antenna so it can measure the power passing to the antenna.

Memory hook: Meter sits in the line.

T4A06: What signals are used in a computer-radio interface for digital mode operation?
  • A. Receive and transmit mode, status, and location
  • B. Antenna and RF power
  • C. Receive audio, transmit audio, and transmitter keying ✓
  • D. NMEA GPS location and DC power
Why, and a memory hook

A computer-radio interface for digital modes carries receive audio, transmit audio and a transmitter keying (PTT) signal.

Memory hook: Audio in, audio out, key.

T4A07: Which of the following is one of the connections required between a computer and a transceiver to operate digital modes?
  • A. Computer “line out” to transceiver push-to-talk
  • B. Computer “line in” to transceiver push-to-talk
  • C. Computer “line in” to transceiver speaker connector ✓
  • D. Computer “line out” to transceiver speaker connector
Why, and a memory hook

The computer's audio "line in" connects to the transceiver's speaker or audio output connector so the computer receives what the radio hears.

Memory hook: Radio speaker feeds computer in.

T4A08: Which of the following conductors is preferred for bonding at RF?
  • A. Copper braid removed from coaxial cable
  • B. Copper-clad steel wire
  • C. Twisted-pair cable
  • D. Flat copper strap ✓
Why, and a memory hook

Flat copper strap has low inductance and so provides the best bonding at RF. Round wire has higher impedance at radio frequencies.

Memory hook: Strap beats wire at RF.

T4A09: How can you determine the length of time that equipment can be powered from a battery?
  • A. Divide the watt-hour rating of the battery by the peak power consumption of the equipment
  • B. Divide the battery ampere-hour rating by the average current draw of the equipment ✓
  • C. Multiply the watts per hour consumed by the equipment by the battery power rating
  • D. Multiply the square of the current rating of the battery by the input resistance of the equipment
Why, and a memory hook

Divide the battery's ampere-hour rating by the average current the equipment draws to estimate run time in hours.

Memory hook: Amp-hours divided by amps equals hours.

T4A10: What function does a digital mode hotspot perform for nearby transceivers?
  • A. Communication with a digital voice or data network ✓
  • B. FT8 digital communications via AFSK using a smartphone connected to the internet
  • C. RTTY encoding and decoding without a computer
  • D. High-speed digital communications for meteor scatter
Why, and a memory hook

A digital mode hotspot links nearby transceivers to a digital voice or data network, usually through the internet.

Memory hook: Hotspot = on-ramp to digital network.

T4A11: Where should the negative power return of a mobile transceiver be connected in a vehicle?
  • A. At the 12-volt battery chassis ground ✓
  • B. To the shell of the power connector
  • C. To any metal part of the vehicle
  • D. Through the transceiver’s mounting bracket
Why, and a memory hook

The negative return of a mobile transceiver should connect at the vehicle's 12-volt battery chassis ground, giving a solid, low-resistance return path.

Memory hook: Negative goes to battery ground.

T4A12: What is an electronic keyer?
  • A. A device for switching antennas from transmit to receive
  • B. A device for voice activated switching from receive to transmit
  • C. A device that assists in manual sending of Morse code ✓
  • D. An interlock to prevent unauthorized use of a radio
Why, and a memory hook

An electronic keyer is a device that assists in manual sending of Morse code by generating properly timed dots and dashes.

Memory hook: Keyer = Morse helper.

T4B (11 questions, 1 on your exam)

T4B01: What is the effect of excessive microphone gain on SSB transmissions?
  • A. Frequency instability
  • B. Distorted transmitted audio ✓
  • C. Increased SWR
  • D. Sideband inversion
Why, and a memory hook

Excessive microphone gain overdrives the transmitter and causes distorted, splattering audio on SSB.

Memory hook: Too much mic gain means a distorted signal.

T4B02: Which of the following can be used to enter a transceiver’s operating frequency?
  • A. The keypad or VFO knob ✓
  • B. The CTCSS or DTMF encoder
  • C. The Automatic Frequency Control
  • D. All these choices are correct
Why, and a memory hook

You can enter the operating frequency with the keypad or tune it with the VFO knob.

Memory hook: Keypad or knob.

T4B03: How is squelch adjusted so that a weak FM signal can be heard?
  • A. Set the squelch threshold so that receiver output audio is on all the time ✓
  • B. Turn up the audio level until it overcomes the squelch threshold
  • C. Turn on the anti-squelch function
  • D. Enable squelch enhancement
Why, and a memory hook

To hear weak FM signals, set the squelch threshold so receiver audio is on all the time, then raise it just until the noise quiets. That is the most sensitive setting.

Memory hook: Open the squelch to hear weak signals.

T4B04: What does an FM signal sound like when received slightly off frequency?
  • A. The audio increases in pitch
  • B. The audio decrease in pitch
  • C. There is no effect except for reduction in amplitude
  • D. The audio becomes distorted ✓
Why, and a memory hook

An FM signal received slightly off frequency sounds distorted, because the receiver's detector is not centered on the signal.

Memory hook: Off frequency, distorted audio.

T4B05: What does the scanning function of an FM transceiver do?
  • A. Checks incoming signal deviation
  • B. Prevents interference to nearby repeaters
  • C. Tunes through a range of frequencies to check for activity ✓
  • D. Tunes through a range of frequencies to determine the antenna’s resonant frequency
Why, and a memory hook

Scanning tunes through a range of frequencies or memory channels to check for activity.

Memory hook: Scan = search for activity.

T4B06: Which of the following controls could be used if the voice pitch of a single-sideband signal returning to your CQ call seems too high or low?
  • A. The AGC or limiter
  • B. The bandwidth selection
  • C. The tone squelch
  • D. The RIT or Clarifier ✓
Why, and a memory hook

The RIT (receiver incremental tuning) or clarifier control shifts the receive frequency without moving the transmit frequency, correcting the pitch of a sideband voice.

Memory hook: RIT fixes the Donald Duck voice.

T4B07: What is a DMR “code plug”?
  • A. An adapter cable used to connect a DMR radio to a computer for internet access
  • B. Configuration data loaded onto your radio to access repeaters and talkgroups ✓
  • C. An upgrade to DMR programming software provided by the radio manufacturer to accommodate new radio models
  • D. A Coder-Decoder (CODEC) that converts analog voice data to DMR digital data and vice versa
Why, and a memory hook

A DMR code plug is the configuration data loaded into your radio so it can access repeaters and talkgroups.

Memory hook: Code plug = radio's programming file.

T4B08: What is the advantage of having a choice of receiver filter bandwidths in a multimode transceiver?
  • A. Permits monitoring several modes simultaneously by selecting a separate filter for each mode
  • B. Permits noise or interference reduction by selecting a bandwidth matching the mode ✓
  • C. Increases the number of frequencies that can be stored in memory
  • D. Increases the amount of offset between receive and transmit frequencies
Why, and a memory hook

A choice of filter bandwidths lets you match the filter to the mode, reducing noise and interference.

Memory hook: Narrow filters cut noise.

T4B09: How is a specific group of stations selected on a DMR digital voice transceiver?
  • A. By retrieving the frequencies from transceiver memory
  • B. By enabling the group’s CTCSS tone
  • C. By entering the group’s identification code ✓
  • D. By inserting a five-pin, pre-programmed code plug
Why, and a memory hook

On DMR you select a specific group of stations by entering the group's identification code (talkgroup ID).

Memory hook: Talkgroup ID chooses the group.

T4B10: Which of the following receiver filter bandwidths provides the best signal-to-noise ratio for SSB reception?
  • A. 500 Hz
  • B. 1000 Hz
  • C. 2400 Hz ✓
  • D. 5000 Hz
Why, and a memory hook

SSB needs roughly 2.4 kHz of bandwidth, so a 2400 Hz filter passes the signal while rejecting the most noise. Wider filters let in more noise; narrower ones cut the voice.

Memory hook: SSB filter: 2400 Hz.

T4B11: Which of the following must be programmed into a D-STAR digital transceiver before transmitting?
  • A. Your call sign ✓
  • B. Your output power
  • C. The codec type being used
  • D. All these choices are correct
Why, and a memory hook

A D-STAR transceiver must be programmed with your call sign before transmitting, since D-STAR sends it with the digital data.

Memory hook: D-STAR knows your call.

Test yourself on these

Take a free 35-question practice exam drawn one per group, just like the real thing.

Start the free practice test

← T3: Radio Wave PropagationAll subelementsT5: Electrical Principles →

Sources

  1. NCVEC: 2026–2030 Technician Question Pool (public release and errata)
  2. 47 CFR § 97.503: Element standards (35 questions, 26 to pass)

Want the why behind all 409 questions?

Ham Tech Exam is a Technician study app that explains every answer with a memory hook. Join the list to get the beta first and the launch-day price.

One email when the beta opens, one at launch. No spam. Unsubscribe anytime by emailing [email protected].