Ham Tech Exam โ€บ Technician frequency chart

Technician frequency chart (2026)

Updated November 20, 2026 ยท based on 47 CFR ยงยง 97.301, 97.305, 97.307 and 97.313 (ITU Region 2, continental US)

Check any frequency. Type a frequency in MHz to see whether a Technician can transmit there, with which modes and how much power.

BandTechnician frequenciesModesMax powerNotes
80 m3.525โ€“3.600 MHzCW only200 W PEP
40 m7.025โ€“7.125 MHzCW only200 W PEP
15 m21.025โ€“21.200 MHzCW only200 W PEP
10 m28.000โ€“28.300 MHzCW, RTTY, data (FT8, etc.)200 W PEP
10 m28.300โ€“28.500 MHzCW, SSB voice200 W PEPOnly HF voice for Technicians
6 m50โ€“54 MHzAll (50.0โ€“50.1 CW only)1,500 W PEPSporadic-E openings in summer
2 m144โ€“148 MHzAll (144.0โ€“144.1 CW only)1,500 W PEPMost repeaters; 146.52 simplex
1.25 m222โ€“225 MHzAll1,500 W PEP
70 cm420โ€“450 MHzAll1,500 W PEPRepeaters, satellites; 50 W PEP limit near some military sites
33 cm902โ€“928 MHzAll1,500 W PEPShared band; 50 W PEP near White Sands
23 cm1240โ€“1300 MHzAll1,500 W PEP
13 cm2300โ€“2310 MHzAll1,500 W PEP
13 cm2390โ€“2450 MHzAll1,500 W PEP
5 cm5650โ€“5925 MHzAll1,500 W PEP
3 cm10000โ€“10500 MHzAll1,500 W PEP
1.2 cm24000โ€“24250 MHzAll1,500 W PEP

Bands above 1.2 cm (47 GHz and up) are also available to Technicians. Some segments are shared with other services, where amateurs are secondary and must not cause interference. Always tune a few kHz inside band edges.

How to read this chart

HF (below 30 MHz): Technicians have four slices. Three are CW (Morse code) only: 3.525โ€“3.600, 7.025โ€“7.125 and 21.025โ€“21.200 MHz. On 10 meters, 28.000โ€“28.300 MHz allows CW, RTTY and data such as FT8, and 28.300โ€“28.500 MHz allows CW and SSB voice. Power is limited to 200 W PEP in all of these segments (ยง 97.313(c)).

VHF, UHF and microwave (above 50 MHz): Technicians have the same privileges as every other license class, up to 1,500 W PEP. The only mode restriction is that the bottom 100 kHz of 6 m (50.0โ€“50.1 MHz) and 2 m (144.0โ€“144.1 MHz) are CW only, for every license class.

What's missing compared with General: HF voice outside 10 m, and the 160, 60, 30, 20, 17 and 12 meter bands. See Technician vs. General.

Exam questions about Technician privileges

Subelement T1B is all about frequencies and power. Here are four from the 2026โ€“2030 pool:

T1B01: Which of the following frequency ranges are available for phone operation by Technician licensees?
  • A. 28.050 MHz to 28.150 MHz
  • B. 28.100 MHz to 28.300 MHz
  • C. 28.300 MHz to 28.500 MHz โœ“
  • D. 28.500 MHz to 28.600 MHz

Why: Technician HF phone privileges are limited to 28.300 to 28.500 MHz in the 10-meter band. All of the other listed ranges are outside Technician phone privileges. [97.301(e), 97.305]

Memory hook: Techs get ten meters, 28.3 to 28.5.

T1B06: On which HF bands does a Technician class operator have phone privileges?
  • A. None
  • B. 10-meter band only โœ“
  • C. 80-meter, 40-meter, 15-meter, and 10-meter bands
  • D. 30-meter band only

Why: On HF, Technicians have phone privileges only in the 10-meter band, 28.300 to 28.500 MHz. [97.301(e)]

Memory hook: Tech HF voice: ten meters only.

T1B11: What is the maximum peak envelope power output for Technician class operators in their HF band segments?
  • A. 200 watts โœ“
  • B. 100 watts
  • C. 50 watts
  • D. 10 watts

Why: Technicians are limited to 200 watts PEP output in their HF segments. [97.313(i)]

Memory hook: Tech on HF: 200 watts.

T1B12: Except for some specific restrictions, what is the maximum peak envelope power output for Technician class operators using frequencies above 30 MHz?
  • A. 50 watts
  • B. 100 watts
  • C. 500 watts
  • D. 1500 watts โœ“

Why: Above 30 MHz, the general limit is 1500 watts PEP, though you must use the minimum power needed and some segments have lower limits. [97.313]

Memory hook: VHF and up: 1500 watts, but use only what you need.

Browse every T1 question in the question pool browser, or read what you can do with a Technician license.

Sources

  1. 47 CFR ยง 97.301: Authorized frequency bands
  2. 47 CFR ยง 97.305: Authorized emission types
  3. 47 CFR ยง 97.307: Emission standards (Technician CW-only and SSB-only notes)
  4. 47 CFR ยง 97.313: Transmitter power standards (200 W PEP for Technicians on HF)
  5. ARRL: Frequency Allocations (US amateur band chart)

Want the why behind all 409 questions?

Ham Tech Exam is a Technician study app that explains every answer with a memory hook. Join the list to get the beta first and the launch-day price.

One email when the beta opens, one at launch. No spam. Unsubscribe anytime by emailing [email protected].