Ham Tech Exam โ€บ Question pool โ€บ T0

T0: Safety questions (2026โ€“2030 Technician pool)

36 questions in the pool ยท 3 on your exam ยท official NCVEC 2026โ€“2030 pool (public domain)

All 36 questions from subelement T0, Safety, with the correct answer marked. Your exam draws one question from each group below, so you'll see 3 T0 questions. On test day the answer order can be shuffled, so learn the answer, not the letter. Tap "Why" for a plain-English explanation.

Groups: T0A ยท T0B ยท T0C

T0A (12 questions, 1 on your exam)

T0A01: Which of the following is a safety hazard of a 12-volt storage battery that lacks internal protection circuitry?
  • A. Touching both terminals with your hands can cause electrical shock
  • B. Shorting the terminals can cause burns, fire, or an explosion โœ“
  • C. RF emissions from a nearby transmitter can cause the electrolyte to emit poison gas
  • D. All these choices are correct
Why, and a memory hook

Shorting the terminals of a 12-volt storage battery can cause burns, fire or an explosion because of the very high current.

Memory hook: Shorted battery = fire.

T0A02: What health hazard is posed by electrical current flowing through the body?
  • A. It may cause injury by heating body tissue
  • B. It may disrupt the electrical functions of cells
  • C. It may cause involuntary muscle contractions
  • D. All these choices are correct โœ“
Why, and a memory hook

Current through the body can cause muscle contraction, heart fibrillation and burns, so all the listed hazards are real.

Memory hook: Current can burn, freeze muscles, stop the heart.

T0A03: In the United States, what circuit does black wire insulation indicate in a three-wire 120 V AC cable?
  • A. Neutral
  • B. Hot โœ“
  • C. Equipment ground
  • D. Negative
Why, and a memory hook

In US AC wiring black insulation indicates the hot conductor.

Memory hook: Black is hot.

T0A04: What is the purpose of a fuse in an electrical circuit?
  • A. To prevent power supply ripple from damaging a component
  • B. To remove power in case of an overload โœ“
  • C. To limit current and prevent shocks
  • D. All these choices are correct
Why, and a memory hook

A fuse removes power by melting in case of an overload.

Memory hook: Fuse blows to protect.

T0A05: Why should a 5-ampere fuse never be replaced with a 20-ampere fuse?
  • A. The larger fuse would be likely to blow because it is rated for higher current
  • B. The power supply ripple would greatly increase
  • C. Excessive current could cause a fire โœ“
  • D. Voltage drop in the higher current fuse could result in excessively low voltage to the device
Why, and a memory hook

A 20-ampere fuse allows much more current than a 5-ampere circuit's wiring can handle, so excessive current could cause a fire.

Memory hook: Bigger fuse, bigger fire risk.

T0A06: What is a good way to guard against electrical shock at your station?
  • A. Use three-wire cords and plugs for all AC powered equipment
  • B. Connect all AC powered station equipment to a common safety ground
  • C. Ensure all capacitors used for high-voltage DC are fully discharged before working inside equipment
  • D. All these choices are correct โœ“
Why, and a memory hook

Use the lowest-voltage equipment, ground the equipment, and use ground-fault circuit interrupters, so all the choices help guard against shock.

Memory hook: Ground it, protect it, GFCI it.

T0A07: Where should a lightning arrester be installed in a coaxial feed line?
  • A. At the output connector of a transceiver
  • B. At the antenna feed point
  • C. At the AC power service panel
  • D. On a grounded panel near where feed lines enter the building โœ“
Why, and a memory hook

A lightning arrester should be installed in the coax on a grounded panel near where feed lines enter the building.

Memory hook: Arrester at the entry panel, grounded.

T0A08: Where should a fuse or circuit breaker be installed in a 120V AC power circuit?
  • A. In series with the hot conductor only โœ“
  • B. In series with the hot and neutral conductors
  • C. In parallel with the hot conductor only
  • D. In parallel with the hot and neutral conductors
Why, and a memory hook

A fuse or circuit breaker in a 120 V AC circuit goes in series with the hot conductor only, never in the neutral or ground.

Memory hook: Fuse the hot only.

T0A09: What should be done to all external ground rods or earth connections?
  • A. Waterproof them with silicone caulk or electrical tape
  • B. Keep them as far apart as possible
  • C. Bond them together with heavy wire or conductive strap โœ“
  • D. Tune them for resonance on the lowest frequency of operation
Why, and a memory hook

All external ground rods and earth connections should be bonded together with heavy wire or conductive strap, to keep them at the same potential.

Memory hook: Bond all grounds together.

T0A10: What hazard exists when rapidly charging or discharging an unprotected battery?
  • A. Overheating or out-gassing โœ“
  • B. Excess output ripple
  • C. Electric shock
  • D. Overvoltage
Why, and a memory hook

Rapidly charging or discharging an unprotected battery can cause overheating or out-gassing.

Memory hook: Fast charge, hot battery.

T0A11: What hazard exists in a power supply immediately after turning it off?
  • A. Circulating currents in the dc filter
  • B. Leakage flux in the power transformer
  • C. Voltage transients from kickback diodes
  • D. Charge stored in filter capacitors โœ“
Why, and a memory hook

After a power supply is turned off, charge can remain stored in the filter capacitors and shock you.

Memory hook: Capacitors hold a charge.

T0A12: Which of the following precautions should be taken when measuring high voltages with a voltmeter?
  • A. Ensure that the voltmeter has very low impedance
  • B. Ensure that the voltmeter and its leads are rated for use at the voltages being measured โœ“
  • C. Ensure that the circuit is grounded through the voltmeter
  • D. Ensure that the voltmeter is set to the correct frequency
Why, and a memory hook

When measuring high voltages, make sure the voltmeter and its leads are rated for use at those voltages.

Memory hook: Rate the meter and leads for the voltage.

T0B (11 questions, 1 on your exam)

T0B01: Which of the following is good practice when installing ground wires on a tower for lightning protection?
  • A. Put a drip loop in the ground connection to prevent water damage to the ground system
  • B. Make sure all ground wire bends are right angles
  • C. Ensure that connections are short and direct โœ“
  • D. All these choices are correct
Why, and a memory hook

Lightning ground connections should be short and direct, because long or indirect paths have high inductance and resist current.

Memory hook: Short and straight to ground.

T0B02: What is required when climbing an antenna tower?
  • A. Have sufficient training on safe tower climbing techniques
  • B. Use appropriate tie-off to the tower at all times
  • C. Always wear an approved climbing harness
  • D. All these choices are correct โœ“
Why, and a memory hook

When climbing an antenna tower you need a helper or observer, a safety harness/lanyard, and a hard hat, so all the choices apply.

Memory hook: Helper, harness, hard hat.

T0B03: Under what circumstances is it safe to climb a tower without a helper or observer?
  • A. When no electrical work is being performed
  • B. When no mechanical work is being performed
  • C. When the work being done is not more than 20 feet above the ground
  • D. Never โœ“
Why, and a memory hook

It is never safe to climb a tower without a helper or observer.

Memory hook: Never climb alone.

T0B04: Which of the following is an important safety precaution to observe when putting up an antenna tower?
  • A. Wear a ground strap connected to your wrist at all times
  • B. Insulate the base of the tower to avoid lightning strikes
  • C. Look for and stay clear of any overhead electrical wires โœ“
  • D. All these choices are correct
Why, and a memory hook

When putting up a tower, look for and stay clear of any overhead electrical wires.

Memory hook: Watch for power lines.

T0B05: What is the purpose of a safety wire through a turnbuckle used to tension guy lines?
  • A. Secure the guy line if the turnbuckle breaks
  • B. Prevent loosening of the turnbuckle from vibration โœ“
  • C. Provide a ground path for lightning strikes
  • D. Provide an ability to measure for proper tensioning
Why, and a memory hook

A safety wire through a turnbuckle prevents it from loosening from vibration.

Memory hook: Safety wire stops loosening.

T0B06: What is the minimum safe distance from a power line to allow when installing an antenna?
  • A. Add the height of the antenna to the height of the power line and multiply by a factor of 1.5
  • B. The height of the power line above ground
  • C. 1/2 wavelength at the operating frequency
  • D. Enough so that if the antenna falls, no part of it can come within 10 feet of the power wires โœ“
Why, and a memory hook

Allow enough clearance that if the antenna falls, no part of it can come within 10 feet of the power wires.

Memory hook: Stay 10 feet clear of power lines.

T0B07: Which of the following is an important safety rule to remember when using a crank-up tower?
  • A. This type of tower must never be painted
  • B. This type of tower must never be grounded
  • C. This type of tower must not be climbed unless it is retracted, or mechanical safety locking devices have been installed โœ“
  • D. All these choices are correct
Why, and a memory hook

A crank-up tower must not be climbed unless it is retracted or mechanical safety locking devices are installed, since it could collapse.

Memory hook: Retract or lock the tower first.

T0B08: Which is a proper grounding method for a tower?
  • A. A single four-foot ground rod, driven into the ground no more than 12 inches from the base
  • B. A ferrite-core RF choke connected between the tower and ground
  • C. A connection between the tower base and a cold-water pipe
  • D. Separate eight-foot ground rods for each tower leg, bonded to the tower and each other โœ“
Why, and a memory hook

A proper tower grounding method is separate eight-foot ground rods for each tower leg, bonded to the tower and to each other.

Memory hook: Eight-foot rods on every leg, bonded.

T0B09: Why should you avoid attaching an antenna to a utility pole?
  • A. The antenna will not work properly because of induced voltages
  • B. The antenna may unbalance the power transformer, causing power fluctuations
  • C. The antenna could contact high-voltage power lines โœ“
  • D. All these choices are correct
Why, and a memory hook

An antenna attached to a utility pole could contact high-voltage power lines.

Memory hook: Utility poles carry power.

T0B10: Which of the following is true when installing grounding conductors used for lightning protection?
  • A. Use only non-insulated wire
  • B. Wires must be carefully routed with precise right-angle bends
  • C. Sharp bends must be avoided โœ“
  • D. Common grounds must be avoided
Why, and a memory hook

Sharp bends must be avoided in lightning protection grounding conductors, because they increase impedance and can make the lightning arc across.

Memory hook: No sharp bends.

T0B11: Which of the following establishes grounding requirements for an amateur radio tower or antenna?
  • A. FCC Part 97 rules
  • B. Local electrical codes โœ“
  • C. FAA tower lighting regulations
  • D. UL recommended practices
Why, and a memory hook

Local electrical codes establish grounding requirements for an amateur radio tower or antenna.

Memory hook: Local codes rule.

T0C (13 questions, 1 on your exam)

T0C01: What type of radiation are radio signals?
  • A. Gamma radiation
  • B. Ionizing radiation
  • C. Alpha radiation
  • D. Non-ionizing radiation โœ“
Why, and a memory hook

Radio signals are non-ionizing radiation. They do not have enough energy to ionize atoms or break chemical bonds.

Memory hook: Radio is non-ionizing.

T0C02: Which of the following bands has the lowest maximum permissible exposure for RF safety?
  • A. 3.5 MHz
  • B. 50 MHz โœ“
  • C. 440 MHz
  • D. 1296 MHz
Why, and a memory hook

The FCC maximum permissible exposure is lowest in the 30 to 300 MHz range, as the body absorbs the most energy there, so 50 MHz is the most restrictive of the listed bands. [1.1310]

Memory hook: The body absorbs VHF best.

T0C03: How does the allowable power density for RF safety change if duty cycle changes from 100 percent to 50 percent?
  • A. It increases by a factor of 3
  • B. It decreases by 50 percent
  • C. It increases by a factor of 2 โœ“
  • D. There is no adjustment allowed for lower duty cycle
Why, and a memory hook

Allowable power density is based on average exposure, so halving the duty cycle from 100% to 50% allows an increase by a factor of 2.

Memory hook: Half the transmit time, double the allowed power density.

T0C04: What factors affect the RF exposure of people near an amateur station antenna?
  • A. Frequency and power level of the RF field
  • B. Distance from the antenna to a person
  • C. Radiation pattern of the antenna
  • D. All these choices are correct โœ“
Why, and a memory hook

RF exposure depends on the power, the antenna gain and type, the distance, and the duty cycle, so all the listed factors matter.

Memory hook: Power, antenna, distance, duty cycle.

T0C05: Why do exposure limits vary with frequency?
  • A. Lower frequency RF fields have more energy than higher frequency fields
  • B. Lower frequency RF fields do not penetrate the human body
  • C. Higher frequency RF fields are transient in nature
  • D. The human body absorbs more RF energy at some frequencies than at others โœ“
Why, and a memory hook

The body absorbs more RF energy at some frequencies than others, so exposure limits vary with frequency.

Memory hook: Body absorbs some frequencies more.

T0C06: Which of the following is an acceptable method to determine whether your station complies with FCC RF exposure regulations?
  • A. By calculation based on FCC OET Bulletin 65
  • B. By calculation based on computer modeling
  • C. By measurement of field strength using calibrated equipment
  • D. All these choices are correct โœ“
Why, and a memory hook

You can determine RF compliance using FCC OET Bulletin 65 calculations, computer modeling, or measurement, so all the choices are acceptable methods. [97.13(c)]

Memory hook: Calculate, model or measure.

T0C07: What hazard is created by touching an antenna during a transmission?
  • A. Electrocution
  • B. RF burn to skin โœ“
  • C. Exposure to ionizing radiation
  • D. All these choices are correct
Why, and a memory hook

Touching an antenna during transmission can cause an RF burn to the skin.

Memory hook: Hot antenna burns.

T0C08: Which of the following actions can reduce exposure to RF radiation?
  • A. Relocate antennas โœ“
  • B. Relocate the transmitter
  • C. Increase the duty cycle
  • D. All these choices are correct
Why, and a memory hook

Relocating antennas increases distance from people and reduces exposure. Exposure falls quickly with distance.

Memory hook: Move the antenna away.

T0C09: How can you make sure your station stays in compliance with RF safety regulations?
  • A. By informing the FCC of any changes made in your station
  • B. By re-evaluating the station whenever an item in the transmitter or antenna system is changed โœ“
  • C. By making sure your antennas have low SWR
  • D. By using only Underwriter Laboratories approved transmitting equipment
Why, and a memory hook

Re-evaluate your station whenever an item in the transmitter or antenna system is changed, to stay in compliance with RF safety rules. [97.13(c)]

Memory hook: Change gear, re-check safety.

T0C10: Why is duty cycle one of the factors used to determine safe RF radiation exposure levels?
  • A. It affects the average exposure to radiation โœ“
  • B. It affects the peak exposure to radiation
  • C. It takes into account the antenna feed line loss
  • D. It takes into account the thermal effects of the final amplifier
Why, and a memory hook

Duty cycle affects the average exposure to radiation, since a transmitter that is on less of the time delivers less average energy.

Memory hook: Duty cycle sets average exposure.

T0C11: What is the definition of duty cycle during the averaging time for RF exposure?
  • A. The difference between the lowest and highest power output of a transmitter
  • B. The difference between the PEP and the average power output of a transmitter
  • C. The percentage of time that a transmitter is transmitting โœ“
  • D. The percentage of time that a transmitter is not transmitting
Why, and a memory hook

Duty cycle is the percentage of time that a transmitter is transmitting during the averaging time.

Memory hook: Duty cycle = percent on.

T0C12: How does RF radiation differ from ionizing radiation (radioactivity)?
  • A. RF radiation does not have sufficient energy to cause chemical changes in cells and damage DNA โœ“
  • B. RF radiation can only be detected with an RF dosimeter
  • C. RF radiation is limited in range to a few feet
  • D. RF radiation is perfectly safe
Why, and a memory hook

RF radiation does not have enough energy to cause chemical changes in cells and damage DNA, unlike ionizing radiation.

Memory hook: Radio is too weak to break DNA.

T0C13: Who is responsible for ensuring that no person is exposed to RF energy above the FCC exposure limits?
  • A. The FCC
  • B. The station licensee โœ“
  • C. Anyone who is near an antenna
  • D. The local zoning board
Why, and a memory hook

The station licensee is responsible for ensuring that no one is exposed to RF energy above the FCC limits. [97.13(c)]

Memory hook: Licensee is responsible.

Test yourself on these

Take a free 35-question practice exam drawn one per group, just like the real thing.

Start the free practice test

โ† T9: Antennas and Feed LinesAll subelements

Sources

  1. NCVEC: 2026โ€“2030 Technician Question Pool (public release and errata)
  2. 47 CFR ยง 97.503: Element standards (35 questions, 26 to pass)

Want the why behind all 409 questions?

Ham Tech Exam is a Technician study app that explains every answer with a memory hook. Join the list to get the beta first and the launch-day price.

One email when the beta opens, one at launch. No spam. Unsubscribe anytime by emailing [email protected].